| NYLON 6/6 IMPACT MODIFIED SUPERTOUGH® | ||||
| ZYTEL® 801 NC010 SUPERTOUGH® | ||||
| Dupont Engineering Polymers / Supertough Nylon 6/6 | ||||
| Nylon
6/6 impact modified has the advantage of very high impact strength at
low temperatures and enhanced resistance to heat distortion over
general purpose nylon 6/6. Impact modified 6/6 nylon is off white in color. |
||||
| APPLICATIONS | ||||
| Fasteners
– Bearings – Gears – Cams – Printed Circuit Board Hardware –
Washers – Spacers – Insulators – Electronic Components – Bushings – Requiring additional impact resistance. |
||||
| Properties | ||||
| Strength | Units | Test Method | DAM | 50%RH |
| Tensile Strength | ||||
| -40°F | psi | ASTM D638 | 11,600 | 10,000 |
| 73°F | psi | ASTM D638 | 7,500 | 6,000 |
| 170°F | psi | ASTM D638 | 5,900 | * |
| 250°F | psi | ASTM D638 | 5,000 | * |
| Elongation at Break(4) | ||||
| -40°F | % | ASTM D638 | 20 | 10 |
| 73°F | % | ASTM D638 | 60 | 210 |
| 170°F | % | ASTM D638 | 220 | 170 |
| 250°F | % | ASTM D638 | 275 | * |
| Stiffness & Creep | Units | Test Method | DAM | 50%RH |
| Flexural Modulus | ||||
| -40°F | psi | ASTM D790 | 285,000 | 340,000 |
| 73°F | psi | ASTM D790 | 245,000 | 125,000 |
| 170°F | psi | ASTM D790 | 69,000 | 57,000 |
| 250°F | psi | ASTM D790 | 50,000 | 47,000 |
| Compressive Stress at 1% Deformation | psi | ASTM D695 | 1,900 | * |
| Deflection Temperature | ||||
| 60 psi (1) | °F | ASTM D648 | 421 | * |
| 264 psi (1) | °F | ASTM D648 | 160 | * |
| Toughness | Units | Test Method | DAM | 50%RH |
| Izod Impact Strength | ||||
| -40°F | ft. lb./in. | ASTM D256 | 3.0 | 2.6 |
| 73°F | ft. lb./in. | ASTM D256 | 17.0 | 20.0 |
| Tensile Impact Strength | ||||
| Long Specimens 73°F | ft. lb./sq. in. | ASTM D1822 | 280 | 550 |
| Thermal | Units | Test Method | DAM | 50%RH |
| Melting Point (Fisher-Johns) | °F | ASTM D789 | 491 | 491 |
| Electrical | Units | Test Method | DAM | 50%RH |
| Volume Resistivity | ohm/cm | ASTM D257 | 1014 | 1013 |
| Dielectric Constant | ||||
| 1000 Hz | ASTM D150 | 3.2 | 4.5 | |
| Dissipation Factor | ||||
| 1000 Hz | ASTM D150 | 2.00 x 10-2 | 0.1 | |
| Flammability | Units | Test Method | DAM | 50%RH |
| UL Flammability Class (3) | UL 94 | 94 HB | ||
| Oxygen Index | % Oxygen | ASTM D2863 | 18 | 19 |
| Miscellaneous | Units | Test Method | DAM | 50%RH |
| Specific Gravity | ASTM D792 | 1.08 | 1.08 | |
| Water Absorption (24 hours) | % | ASTM D570 | 1.2 | * |
| Water Absorption (Saturation) | % | ASTM D570 | 6.7 | * |
| Hardness, Rockwell | ASTM D785 | R112 | R89 | |
| Taber Abrasion CS-17 wheel, 1000 g | mg./1000 cycles | * | 7 | |
| Mold Shrinkage for 1/8" thick (approx.) | in./in. | 0.015 | * | |