DUPONT DELRIN® SUPERTOUGH ACETAL - 100ST (IMPACT MODIFIED) | ||
DELRIN® 100ST NC010 | ||
DuPont Engineering Polymers / Americas - Acetal (POM) Homopolymer | ||
Delrin® acetal resins are thermoplastic polymers made by the polymerization of formaldehyde. Delrin 100 is a high viscosity resin, which shows outstanding physical properties, especially toughness. Delrin is noted for high strength and rigidity in a wide temperature range, fatigue endurance, excellent resistance to moisture, gasolines, solvents, and many other neutral chemicals. High resistance to repeated impacts, resilience, it also has a good wear resistance and low coefficient of friction. | ||
APPLICATIONS | ||
Delrin® can be used in automotive, appliance, plumbing, construction, hardware, electronics, and consumer goods. | ||
Automotive Specifications | ||
• FORD ESB-M4D464-A2 | ||
• FORD WSK-M4D681-A | ||
• GM GMP POM 010 | ||
• GM 7001M (POM) | ||
• CHRYSLER MSDB 100 CPN3248 | ||
• ASTM D4181 POM141 | ||
Properties | ||
Physical | Nominal Values (English) | Test Method |
Density - Specific Gavity | 1.34 sp gr 23°/23°C | ASTM D792 |
Melt Flow Rate (190°C/1.05kg - M) | 0.800 g/10 min | ASTM D1238 |
Mold Shrink, Linear-Flow (0.125 in) | 0.0090 to 0.012 in/in | ASTM D955 |
Mold Shrink, Linear-Trans (0.125 in) | 0.010 to 0.013 in/in | ASTM D955 |
Water Absorption @ Equil (50% RH, 73°F) | 0.35% | ASTM D570 |
Water Absorption @ 24 hrs (73°F) | 0.44% | ASTM D570 |
Water Absorption @ Sat. (73°F) | 0.85% | ASTM D570 |
Mechanical | Nominal Values (English) | Test Method |
Tensile Modulus (73°F) | 190,000psi | ASTM D638 |
Tensile Strength | ASTM D638 | |
(158°F) | 4,700psi | |
(212°F) | 3,400psi | |
(250°F) | 2,600psi | |
Tensile Strength @ Yield (73°F) | 6,500psi | ASTM D638 |
Tensile Elongation @ Yield (73°F) | 35% | ASTM D638 |
Tensile Elongation @ Break | ASTM D638 | |
(73°F) | 150% | |
(158°F) | 250% | |
(212°F) | 250% | |
Flexural Modulus | ASTM D970 | |
(73°F) | 160,000psi | |
(158°F) | 100,000psi | |
(212°F) | 50,000psi | |
(250°F) | 33,000psi | |
Flexural Strength (73°F) | 5,200psi | ASTM D790 |
Shear Strength | 5,000psi | ASTM D732 |
Poisson's Ratio | 0.35 | ASTM E132 |
Coefficient of Friction (vs. Metal - Dynamic) | 0.14 | ASTM D1894 |
Deformation Under Load (2,000psi, 122°F) | 3.00% | ASTM D621 |
Impact | Nominal Values (English) | Test Method |
Notched Izod Impact | ASTM D256 | |
(-40°F) | 4.70 ft-lb/in | |
(73°F) | 16.00 ft-lb/in | |
Unnotched Izod Impact @ (73°F) | No Break ft-lb/in | ASTM D256 |
Tensile Impact Strength @ (73°F) | 750 ft-lb/in² | ASTM D1822 |
Hardness | Nominal Values (English) | Test Method |
Rockwell Hardness | ASTM D785 | |
(M-Scale) | 58 | |
(R-Scale) | 105 | |
Thermal | Nominal Values (English) | Test Method |
DTUL @ 264psi - Unannealed | 142°F | ASTM D648 |
DTUL @ 66psi - Unannealed | 255°F | ASTM D648 |
Melting Point | 352°F | ASTM D3418 |
CLTE, Flow (73°F to 130°F (23°C to 55°C)) | 0.00013 in/in/°F | ASTM D696 |
CLTE, Transverse (73°F to 130°F (23°C to 55°C)) | 7.5E-005 in/in/°F | ASTM D696 |
Rel Temp Indx Mech w/oImp | UL 746 | |
(0.118 in) | 185°F | |
(0.0591 in) | 185°F | |
Rel Temp Indx Mech w/Imp | UL 746 | |
(0.118 in) | 185°F | |
(0.0591 in) | 185°F | |
Rel Temp Indx Elect | UL 746 | |
(0.118 in) | 221°F | |
(0.0591 in) | 221°F | |
Electrical | Nominal Values (English) | Test Method |
Surface Resistivity | 2.0E+014 ohms | ASTM D257 |
Volume Resistivity | 4.0E+014 ohms-cm | ASTM D257 |
Dielectric Strength (0.125 in) | 510 V/mil | ASTM D149 |
Dielectric Constant (1,000,000 Hz) | 4.200 | ASTM D150 |
Dissipation Factor (1,000,000 Hz) | 0.027 | ASTM D150 |
Arc Resistance | 120 sec | ASTM D495 |
Ignition Characteristics | Nominal Values (English) | Test Method |
Flame Rating - UL | UL 94 | |
(0.0591 in) | HB | |
(0.118 in) | HB |