NYLON 6/6 POLYAMIDE (PA) | ||
ZYTEL® 101F NC010 (Dry) (PA) | ||
DuPont Engineering Polymers / Americas - Polymide 66 | ||
General-purpose
nylon 6/6 has good toughness, tensile strength, and resistance to
creep, particularly in the high temperature range. Nylon has excellent wear properties. low coefficient of friction, and exceptional chemical resistance to aromatic hydrocarbons, greases, and oils. Nylon is a hygroscopic material. Moisture acts as a plasticizer reducing the tensile strength, stiffness, and increasing elongation, impact strength, and energy absorbing characteristics. Outdoor weathering can be improved by the addition of carbon black. Nylon will perform well in long range service in most applications at temperatures as high as 185°F (85°C). Nylon is a translucent off white color. |
||
APPLICATIONS | ||
Fasteners
- Bearings - Gears - Cams - Gaskets - Printed Circuit Board Hardware -
Washers - Spacers - Insulators - Spiral Wrap - Flexible Grommeting - Wire Ties - Electronic Components - Bushings - Wiring Clips - Cable Clamps - Hole Plugs - Hose Clamps |
||
Automotive Specifications | ||
• CHEVROLET CMP NY001 AB | ||
• CHRYSLER MSDB 41 CPN2012 Color: Color As Noted On Drawing | ||
• FORD ESF-M4D150-A | ||
• GM GMP PA66 005 | ||
• CHEVROLET CMP NY001 BB | ||
• CHEVROLET CMP NY001 CB | ||
• CHEVROLET CMP NY001 DB | ||
• CHEVROLET CMP NY056 AA | ||
• GM 6063M | ||
• FORD WSK-M4D647-A | ||
• TYCO 100-1422 | ||
• ASTM D4066 PA111 | ||
Approvals | FDA 21CFR 177.1500 | |
Properties | ||
Physical | Nominal Values (English) | Test Method |
Density - Specific Gavity | 1.14 sp gr 23°/23°C | ASTM D792 |
Mold Shrink, Linear-Flow (0.125 in) | 0.015 in/in | ASTM D955 |
Water Absorption @ 24 hrs (73°F) | 1.2% | ASTM D570 |
Water Absorption @ Sat. (73°F) | 8.5% | ASTM D570 |
Mechanical | Nominal Values (English) | Test Method |
Tensile Strength (73°F) | 12,000psi | ASTM D638 |
Tensile Strength @ Yield (73°F) | 12,000psi | ASTM D638 |
Tensile Elongation @ Yield (73°F) | 4.0% | ASTM D638 |
Tensile Elongation @ Break (73°F) | 50.0% | ASTM D638 |
Flexural Modulus | ASTM D970 | |
(73°F) | 410,000psi | |
(250°F) | 78,000psi | |
(170°F) | 100,000psi | |
(-40°F) | 470,000psi | |
Poisson's Ratio | 0.4 | ASTM E132 |
Impact | Nominal Values (English) | Test Method |
Notched Izod Impact @ (73°F) | 1.00 ft-lb/in | ASTM D256 |
Hardness | Nominal Values (English) | Test Method |
Rockwell Hardness | ASTM D785 | |
(M-Scale) | 71 | |
(R-Scale) | 113 | |
Thermal | Nominal Values (English) | Test Method |
DTUL @ 264psi - Unannealed | 149°F | ASTM D648 |
DTUL @ 66psi - Unannealed | 410°F | ASTM D648 |
Brittle Temperature | -112°F | ASTM D746 |
Melting Point | 505°F | |
CLTE, Flow (TMA) (73°F to 130°F (23°C to 55°C)) | 5.5E-005 in/in/°F | ASTM E831 |
CLTE, Transverse (TMA) (73°F to 130°F (23°C to 55°C)) | 6.1E-005 in/in/°F | ASTM E831 |
Specific Heat | 0.650 Btu/lb/°F | ASTM C351 |
Electrical | Nominal Values (English) | Test Method |
Surface Resistivity | 1.0E+014 ohms | ASTM D257 |
Volume Resistivity | 1.0E+015 ohms-cm | ASTM D257 |
Dielectric Strength | ASTM D149 | |
(0.0630 in) | 590 V/mil | |
(0.126 in) | 420 V/mil | |
Dielectric Constant | ASTM D150 | |
(100 Hz) | 4.100 | |
(1000 Hz) | 4.000 | |
(1000000 Hz) | 3.700 | |
Dissipation Factor | ASTM D150 | |
(100 Hz) | 0.010 | |
(1000 Hz) | 0.020 | |
(1000000 Hz) | 0.020 | |
Ignition Characteristics | Nominal Values (English) | Test Method |
Flame Rating - UL | UL 94 | |
(0.0591 in) | V-2 | |
(0.0280 in) | V-2 |